It is essential to measure the rate of the heart when you are engaged in exercising and other physical activities. This will help you burn the required amount of calories and achieve your daily goal with much ease. The measuring is done using a polar heart monitor, which is powered by a polar heart rate monitor battery.
One is therefore advised to take the device to a dealer and have the battery replaced. If you wish to keep the 100% seal (which is also water resistant) and you want to keep your warranty too, you should take the device to an authorized dealer. The dealer will have the power-tool replaced.
If you are interested in 100% keeping your warranty intact, you need to consult a dealer. The dealer will also help in ensuring that the water resistant seal remains intact, and still have the device power system restored. This is the easier way out.
Those interested in doing the replacing at home should make sure that they have a well-fitting screwdriver. Use this to open the four little screws which are located on the back of the polar tool. Then gently remove the back cover of the monitor.
Now remove the inner part of the tool using the same screwdriver. Using the screwdriver, latch the side of the implement and gently force the inner part out from the outer casing. This should now expose the batt in the very inner layer of rater.
After removing the outer back covering, you can then remover the inside unit from the watch casing. The removal is done by pulling of the internal unit from the outer case. You may use a screwdriver to remove the batter tab. Any implement will work just fine; only remember to keep the seal intact.
Through the gentle forcing the batt will be forced out. From here you then need to get the exact same battery from the store, or even from online shops. The batt may be fetched for something close to $3.50. When buying the batt you need to make sure that it matches with the one that has been removed.
The final step involves putting the batter back and fixing everything exactly as it was. When the batter replacing is done nicely, the warrant seal will be safe and you will not have broken the water resistant section. Always remember to use a well-fitting screwdriver when putting back the polar heart rate monitor battery and other sections of the tool. The twist should now be in working order.
One is therefore advised to take the device to a dealer and have the battery replaced. If you wish to keep the 100% seal (which is also water resistant) and you want to keep your warranty too, you should take the device to an authorized dealer. The dealer will have the power-tool replaced.
If you are interested in 100% keeping your warranty intact, you need to consult a dealer. The dealer will also help in ensuring that the water resistant seal remains intact, and still have the device power system restored. This is the easier way out.
Those interested in doing the replacing at home should make sure that they have a well-fitting screwdriver. Use this to open the four little screws which are located on the back of the polar tool. Then gently remove the back cover of the monitor.
Now remove the inner part of the tool using the same screwdriver. Using the screwdriver, latch the side of the implement and gently force the inner part out from the outer casing. This should now expose the batt in the very inner layer of rater.
After removing the outer back covering, you can then remover the inside unit from the watch casing. The removal is done by pulling of the internal unit from the outer case. You may use a screwdriver to remove the batter tab. Any implement will work just fine; only remember to keep the seal intact.
Through the gentle forcing the batt will be forced out. From here you then need to get the exact same battery from the store, or even from online shops. The batt may be fetched for something close to $3.50. When buying the batt you need to make sure that it matches with the one that has been removed.
The final step involves putting the batter back and fixing everything exactly as it was. When the batter replacing is done nicely, the warrant seal will be safe and you will not have broken the water resistant section. Always remember to use a well-fitting screwdriver when putting back the polar heart rate monitor battery and other sections of the tool. The twist should now be in working order.
About the Author:
Visit PolarHeartRateMonitorFT1.net to get a summary of Polar heart rate monitor features and instructions on how to replace Polar heart rate monitor batteries.
No comments:
Post a Comment